For the complete documentation index, see llms.txt. This page is also available as Markdown.

3. Airframe Structure

Tools for this section

Tools.
  • 2 mm hex screwdriver

  • Pliers

Parts for this section

Parts for this section.
(8x) M3x30mm Flat Head Screws, M3 Washers, and Nylon Lock Nut.

Parts:

  • Airframe Bottom

  • Main Body

  • (4x) Arm Brackets

  • (4x) Landing Gears

  • (4x) Arm Alignment Tool

  • (4x) Arm Assemblies (from Section 2.)

Fasteners:

  • (8x) M3x30mm Flat Head Screws

  • (8x) M3 Washer

  • (8x) M3 Nylon Lock Nut

Step 1: Airframe Stack

Parts before stacking.
Stacked parts.
  • Prepare the Airframe Bottom and Main body.

  • Stack the Main Body on top of the Airframe Bottom.

  • Align the parts.

Antenna Hole.
Correct direction of Airframe Bottom alignment.
Incorrect direction of Airframe Bottom alignment.
  • Ensure the antenna mount hole is facing the correct side.

  • Turn the stack upright to check that the hole is facing the XT-90 Mount side and NOT the FPV Camera Mount side.

Step 2: Arm Bracket Assembly

Aligning Arm Bracker to Airframe Stack.
  • Prepare (1x) Arm Bracket, Airframe Stack, (2x) M3x30mm Flat Head Screws, (2x) M3 Washer, and (2x) M3 Nylon Lock Nut.

  • Align the Arm Bracket to one of the four corners of the Airframe Stack.

  • Insert the M3x30mm Flat Head Screw into the chamfered holes on the Arm Bracket.

  • Ensure the screws are inserted into the center hole of the row of three holes.

  • Align the full stack of parts until the screw ends exit the Airframe Bottom plate.

Screw ends exiting out Airframe Bottom.

Step 3: Landing Gear Assembly

Aligning Landing Gear to the screw ends.
Inserting Landing Gear into screw ends.
  • Prepare the (1x) Landing Gear.

  • Align the center holes on the Landing Gear to the

Step 4: Fastening Arm Bracket

Inserting first M3 Washer.
Inserting second M3 Washer.
  • Prepare (2x) M3 Washer and (2x) M3 Nylon Lock Nut.

  • Insert M3 Washers into each screw end on the bottom of the assembly.

Inserting first M3 Lock Nut.
Inserting second M3 Lock Nut.
  • Loosely screw in the M3 Nylon Lock Nut

Completed assembly.
Completed assembly side view.

Step 5: Repeat

  • Repeat Steps 1-4 for the remaining three corners.

All four Arm Brackets and Landing Gear installed to the airframe.

Step 6: Arm Installation

Inserting Arm Assembly into Arm Bracket.
Arm Tube flushly seated into Arm Bracket.
  • Prepare (4x) Arm Assemblies.

  • Insert one Arm Assembly into the hole of the Arm Bracket on one of the corners.

  • Ensure the Arm Tube is seated all the way.

All four Arm Assemblies seated into airframe.
  • Repeat for the remaining three arms.

Step 7: Arm Alignment

Arm Alignment Tool pre installation.
Arm Alignment Tool installation.
  • Prepare (4x) Arm Alignment Tools.

  • Insert the Arm Alignment Tool peg into the holes in each Motor Mount.

Proper Alignment Tool setup.
Properly seated Arm Tube.
  • Ensure the Alignment Tool peg is in all the way, and the bottom of the Alignment Tool is flush against a flat level surface.

  • Check that the Arm Tube is seated all the way into the Arm Bracket one final time.

All four arms seated with Arm Alignment Tools in place.
  • Repeat for the remaining three arms.

Ensure that all four Alignment Tools are flush against a smooth and level table surface to ensure proper arm alignment.

Step 8: Final Arm Installation

Grabbing the Nylon Lock Nut.
Carefully tightening the screw.
  • Prepare the 2 mm hex screwdriver and Pliers.

  • Grab one of the Nylon Lock Nut underneath the airframe with the pliers.

  • Use the 2mm hex screwdriver to tighten the screw carefully.

  • Gradually tighten the screw until light resistance is felt.

  • Once light resistance is felt, repeat the process for the closest adjacent screw.

  • Repeat this process back and forth until hand tight.

Example of a proper Arm Bracket gap.
  • Ensure that the Arm Bracket gap is even as pictured above.

  • If the gap is uneven, carefully loosen both sides and try to tighten both sides evenly by alternating tightening between each pair of screws.

  • Repeat this step for the remaining three Arm Bracket Assemblies.

Step 9: Final Prep

  • Proceed with a final check to ensure all the arms have been installed level.

  • Gently twist each arm to ensure that the screws are properly tightened.

  • If any movement is present during the twist test, repeat Step 8 for that arm.

  • Once everything is checked and ready, remove the Arm Alignment Tool.

Step 10: Section 3 Finished

Last updated