> For the complete documentation index, see [llms.txt](https://docs.k9defense.tech/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.k9defense.tech/exodus/exodus-dev-technical-resources/forward-payload-i-o.md).

# Forward Payload I/O

Exodus features a Forward Payload Interface to allow intergation of nose mounted optics and sensor payloads.

{% hint style="success" %}
Pin Number 1 is always indicated with a white square.
{% endhint %}

<figure><img src="https://3295908973-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2Fb01HmPjtHDbjVUURluQb%2Fuploads%2F2A74D7Ch2K27Vn34feYJ%2F3453w2s.png?alt=media&amp;token=5d8e9498-6abc-4c1d-a6c5-fddc8a4b61c8" alt=""><figcaption></figcaption></figure>

### Axillary Passthrough  (#13)

{% hint style="info" %}
The Axillary Passthrough is a 10 pin passthrough from inside the drone to the front to allow any custom signal or low power line. Anything assigned to the passthrough port inside the drone in the orders of the 10 pin will be assigned in the same order on the forward aux passthrough port. This port can be used for UART, USB, CAN, etc. from the flight controller or compute payload to any custom sensor or module in the nose of the drone.
{% endhint %}

{% hint style="danger" %}
The Aux passthrough is deigned for low voltage signals rated for 5v at 0.5 amps max (examples: UART, USB 2.0, CAN),&#x20;

DO NOT USE for passing any high current or voltage!&#x20;
{% endhint %}

JST GH (10 Pin)

| Pin Number | Signal |
| ---------- | ------ |
| 1          | Pin 1  |
| 2          | Pin 2  |
| 3          | Pin 3  |
| 4          | Pin 4  |
| 5          | Pin 5  |
| 6          | Pin 6  |
| 7          | Pin 7  |
| 8          | Pin 8  |
| 9          | Pin 9  |
| 10         | Pin 10 |

###

### Servos (#14)

{% hint style="info" %}
This port is mapped to PWM Aux 5 and 6 on the ARK FPV Flight Controller.
{% endhint %}

2.54mm Header Pin (3 Pin)

| Pin Number | Signal |
| ---------- | ------ |
| 1          | PWM    |
| 2          | 5v     |
| 3          | GND    |

###

### ENET 0 (#15)

{% hint style="info" %}
Ethernet-0 Output is connected to both the ENET 0 Connector and the IP Camera Connector. Only one can be used at a time. Use the ENET0 Connector for full gigabit Ethernet, or use the IP Camera Connector for an IP Camera payload.\
\
Ethernet-0 is connected to the onboard gigabit Ethernet Switch.
{% endhint %}

JST GH (8 Pin)

<table><thead><tr><th width="374">Pin Number</th><th>Signal</th></tr></thead><tbody><tr><td>1</td><td>ENET 0 A+ (TX+)</td></tr><tr><td>2</td><td>ENET 0 A- (TX-)</td></tr><tr><td>3</td><td>ENET 0 B+ (RX+)</td></tr><tr><td>4</td><td>ENET 0 B- (RX-)</td></tr><tr><td>5</td><td>ENET 0 C+</td></tr><tr><td>6</td><td>ENET 0 C-</td></tr><tr><td>7</td><td>ENET 0 D+</td></tr><tr><td>8</td><td>ENET 0 D-</td></tr></tbody></table>

###

### IP Camera (#16)

{% hint style="info" %}
Ethernet-0 Output is connected to both the ENET 0 Connector and the IP Camera Connector. Only one can be used at a time. Use the ENET0 Connector for full gigabit Ethernet, or use the IP Camera Connector for an IP Camera payload.\
\
Ethernet-0 is connected to the onboard gigabit Ethernet Switch.
{% endhint %}

JST SH (8Pin)

| Pin Number | Signal    |
| ---------- | --------- |
| 1          | ENET 0 A+ |
| 2          | ENET 0 A- |
| 3          | ENET 0 B+ |
| 4          | 12v       |
| 5          | 12v       |
| 6          | ENET 0 B- |
| 7          | GND       |
| 8          | GND       |

## &#x20;<a href="#id-5v-out-5" id="id-5v-out-5"></a>

## 12v Out (#17) <a href="#id-5v-out-5" id="id-5v-out-5"></a>

XT-30 Male

| Pin Number | Signal             |
| ---------- | ------------------ |
| 1          | GND (Rounded Side) |
| 2          | 12v+ (Flat Side)   |

## &#x20;<a href="#id-5v-out-5" id="id-5v-out-5"></a>

## Battery Voltage Out (#18) <a href="#id-5v-out-5" id="id-5v-out-5"></a>

{% hint style="danger" %}
This output is UNREGULATED RAW BATTERY VOLTAGE!
{% endhint %}

XT-30 Male

| Pin Number | Signal             |
| ---------- | ------------------ |
| 1          | GND (Rounded Side) |
| 2          | VBAT+ (Flat Side)  |

## &#x20;<a href="#id-5v-out-5" id="id-5v-out-5"></a>

## 5v Out (#19) <a href="#id-5v-out-5" id="id-5v-out-5"></a>

XT-30 Male

| Pin Number | Signal             |
| ---------- | ------------------ |
| 1          | GND (Rounded Side) |
| 2          | 5v+ (Flat Side)    |
